Mazda CX-5 Service & Repair Manual: Audio Unit Personalization Features Setting Procedure
Door Locks Systems
1. Switch the ignition ON (engine off or on).
2. Turn the audio unit power on.
3. Select the following from the audio unit screen.
a. “Setup”
b. “Vehicle”
c. “Door Locks“
4. Select the following items and change the setting.
Advanced keyless entry system
|
Audio unit display |
Function |
Initial setting |
Setting contents |
Control module |
|
Auto Re-lock Time |
The operation start time of the auto re-lock function can be changed. |
60 seconds |
30 seconds / 60 seconds / 90 seconds |
Start stop unit |
|
Lock Beep Volume |
The keyless beeper volume can be adjusted. |
Medium |
Off / Low / Medium / High |
Start stop unit |
|
Walk Away Lock |
The out-of-area (reception area) type auto lock function can be set. |
OFF |
OFF / ON |
Start stop unit |
Keyless entry system
|
Audio unit display |
Function |
Initial setting |
Setting contents |
Control module |
|
Auto Re-lock Time |
The operation start time of the auto re-lock function can be changed. |
60 seconds |
30 seconds / 60 seconds / 90 seconds |
Start stop unit |
Power door lock system
|
Audio unit display |
Function |
Initial setting |
Setting contents |
Control module |
|
Unlock Mode |
2-step unlocking system can be set. |
Once Driver's, Twice: All Doors |
Touch Once: ALL Doors / Once Driver's, Twice: All Doors |
Start stop unit |
|
Auto Door Lock Mode |
Auto door lock function can be changed. |
Lock: Driving, Unlock: IGN Off |
OFF / Lock When Driving / Lock: Driving, Unlock: IGN Off / Lock When Shifting Out Of P / Lock: Shift From P, Unlock: In P |
Rear body control module (RBCM) |
Lighting Systems
1. Switch the ignition ON (engine off or on).
2. Turn the audio unit power on.
3. Select the following from the audio unit screen.
a. “Setup”
b. “Vehicle”
c. “Lighting“
4. Select the following items and change the setting.
Turn light system
|
Audio unit display |
Function |
Initial setting |
Setting contents |
Control module |
|
3-Flash Turn Signal |
The turn light system can be switched between operable and inoperable. |
On |
On / Off |
Rear body control module (RBCM) |
Auto light system
|
Audio unit display |
Function |
Initial setting |
Setting contents |
Control module |
|
Auto-headlight On |
Auto light sensor sensitivity can be changed. |
Medium |
Light / Medium Light / Medium / Medium Dark / Dark |
Rear body control module (RBCM) |
NOTE:
-
If the mode is set to “Light” and “Medium Light”, the illumination level for illuminating the TNS and headlight increases. Therefore, the TNS and headlights illuminate when the ambient light is brighter than when the level is set to “Medium”. In addition, if the mode is set to “Medium Dark” and “Dark”, the illumination level for illuminating the TNS and headlights decreases. Therefore, the TNS and headlights illuminate when the ambient light is lower than when the level is set to “Medium”.
Auto light off system
|
Audio unit display |
Function |
Initial setting |
Setting contents |
Control module |
|
Headlight Off Timer |
The headlight emitted time of the auto light off timer can be changed. |
30 seconds. |
120 seconds. / 90 seconds. / 60 seconds. / 30 seconds. / 0 seconds. |
Rear body control module (RBCM) |
Room light control system
|
Audio unit display |
Function |
Initial setting |
Setting contents |
Control module |
|
Interior Light Timeout - Door Open |
The front/rear map light illumination time after any door is open can be changed. |
30 minutes |
60 minutes / 30 minutes / 10 minutes |
Rear body control module (RBCM) |
|
Interior Light Timeout - Door Closed |
The front/rear map light illumination time after any door is closed can be changed. |
15 seconds |
60 seconds / 30 seconds / 15 seconds / 7.5 seconds |
Rear body control module (RBCM) |
Audio Unit (Without Color LCD)
NOTE:
“iPod” is a registered trademark of Apple Inc. in the United States and other
countries.
Outline
The audio unit controls the CD, radio, exterior input devices (AUX/US ...
Audio Unit Removal/Installation
Removal
1. Disconnect the negative battery cable.
2. Remove the decoration panel..
3. Remove the bolt.
4. Remove the screws.
NOTE:
When removing the audio unit, the audio unit cou ...
Other materials:
Brake Fluid Pressure Sensor
Purpose/Function
The brake fluid pressure sensor detects the fluid pressure from the master
cylinder and transmits it to the DSC HU/CM.
Construction
The brake fluid pressure sensor is built into the DSC HU/CM. Therefore if
there is any malfunction of the brake fluid pressur ...
Bumper Bracket Installation [Panel Replacement]
Symbol Mark
Installation Procedure
1. When installing new parts, measure and adjust the body as necessary to conform
with standard dimensions.
2. Drill holes for the plug welding 6 locations indicated by (A) and 3 locations
indicated by (C) shown in the figure, before installing the new ...
Air Bag Module And Pre Tensioner Seat Belt Deployment Procedures [Standard Deployment
Control System]
WARNING:
A live (undeployed) air bag module or pre-tensioner seat belt may accidentally
operate (deploy) when it is disposed of and cause serious injury. Do not dispose
of a live (undeployed) air bag module or pre-tensioner seat belt. If the SSTs
(Deployment tool and Adapter harness ...
