Mazda CX-5 Service & Repair Manual: Front Oil Seal Replacement
WARNING:
-
A hot engine can cause severe burns. Turn off the engine and wait until it is cool before servicing.
1. Remove the front under cover No.2..
2. Remove the splash shield..
3. Remove the drive belt..
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
|
1 |
Crankshaft pulley lock bolt (See Crankshaft Pulley Lock Bolt Removal Note.) (See Crankshaft Pulley Lock Bolt Installation Note.) |
|
2 |
Crankshaft pulley |
|
3 |
Front oil seal (See Front Oil Seal Removal Note.) (See Front Oil Seal Installation Note.) |
Crankshaft Pulley Lock Bolt Removal Note
CAUTION:
-
To prevent damage to the crankshaft pulley, protect the crankshaft pulley with a clean cloth so that the bar part (205-072) of the SST does not contact the crankshaft pulley.
-
To prevent damage to the engine front cover, be careful not to allow the tab part (49 B011 105) of the SST to get caught between the crankshaft pulley and the engine front cover.
1. Hold the crankshaft pulley using the SSTs
.
2. Remove the crankshaft pulley lock bolt.
Front Oil Seal Removal Note
1. Cut the oil seal lip using a utility knife.
2. Remove the oil seal using a flathead screwdriver with the tip protected by a clean cloth to prevent damage to the oil seal sliding part of the crankshaft.
Front Oil Seal Installation Note
1. Apply clean engine oil to the inner surface of a new front oil seal.
2. Insert the front oil seal into the engine front cover by hand.
3. Tap the oil seal in evenly using the SST
and a hammer.
-
Front oil seal press-in amount
-
0—0.5 mm {0—0.019 in}
Crankshaft Pulley Lock Bolt Installation Note
CAUTION:
-
To prevent damage to the crankshaft pulley, protect the crankshaft pulley with a clean cloth so that the bar part (205-072) of the SST does not contact the crankshaft pulley.
-
To prevent damage to the engine front cover, be careful not to allow the tab part (49 B011 105) of the SST to get caught between the crankshaft pulley and the engine front cover.
1. Hold the crankshaft pulley using the SSTs
.
2. Tighten the crankshaft pulley lock bolt in the order shown in the following two steps.
-
Tightening torque
-
Step 1: 90—110 N·m {9.2—11 kgf·m, 67—81 ft·lbf}
-
Step 2: 55—65°
Engine Oil Solenoid Valve
Purpose, Function
The engine oil solenoid valve switches the hydraulic transmission passage
in accordance with the driving conditions and the oil pump drive resistance
is reduced by contr ...
Lubrication System
Outline
Pressure loss is reduced by optimizing the oil passage.
With the adoption of the chain drive type oil pump, oil pump drive force
has been reduced.
With the adoption o ...
Other materials:
Clock Spring Removal/Installation [Two Step Deployment Control System]
CAUTION:
If the disc on the combination switch is deformed or has foreign material
adhering to it, performance of the steering angle sensor may be reduced, causing
abnormal operation. When handling the clock spring, be careful not to deform
the disc and make sure there is no foreign ...
Rain Sensor
Outline
The rain sensor detects the amount of rainfall and calculates the wiper operation
speed, and outputs a windshield wiper control signal to the front body control
module (FBCM) to perform automatic wiper operation (auto wiper system) according
to the amount of rainfall.
...
Selector Lever Inspection
1. Switch the ignition ON (engine off or on).
2. Perform the following procedures to inspect the selector lever.
If there is any malfunction, adjust the selector cable..
a. Verify that the selector lever can be operated as shown in the figure.
b. Verify that the selector lever ...
