Mazda CX-5 Service & Repair Manual: Airflow Mode Control [Full Auto Air Conditioner]
Purpose
-
The airflow mode control changes the airflow mode according to the vehicle environment.
Function
-
The airflow mode control drives the airflow mode actuator according to the mode switch, defroster switch, and the vehicle environment and switches the position of the airflow mode door.
-
The airflow mode control has automatic and manual controls.
-
The airflow mode automatic control performs the following correction:
-
Engine coolant temperature correction (warm-up correction)
Airflow mode automatic control
-
The climate control unit determines the airflow mode based on the current air mix actuator opening angle and solar radiation amount.
-
Determined value used for the airflow mode is changed according to the signal from the solar radiation sensor.
Airflow mode manual control
-
The climate control unit switches the airflow mode based on the MODE switch operation.
|
Airflow mode |
Operation switch |
Air vent |
|
VENT |
Mode switch |
CENTER VENT, SIDE VENT |
|
BI-LEVEL |
CENTER VENT, SIDE VENT, FRONT HEAT, REAR HEAT |
|
|
HEAT |
FRONT HEAT, REAR HEAT, SIDE DEMISTER (low volume), DEFROSTER (low volume), SIDE VENT (low volume) |
|
|
DEF/HEAT |
FRONT HEAT, REAR HEAT, SIDE DEMISTER, DEFROSTER, SIDE VENT (low volume) |
|
|
DEFROSTER |
DEFROSTER switch |
SIDE DEMISTER, DEFROSTER, SIDE VENT (low volume) |
Correction
-
Engine coolant temperature correction (warm-up correction)
-
The engine coolant temperature correction (warm-up correction) prevents cold air from coming out of the lower vents after engine start in winter.
-
The engine coolant temperature correction (warm-up correction) switches the airflow mode according to the increase in the engine coolant temperature.
Construction
-
The airflow volume control consists of the parts indicated in the following table:
|
Input device |
Control part |
Output device |
|
|
|
Operation
1. The climate control unit determines the airflow mode based on the operations of the mode and defroster switches and signals from each sensor which changes according to the vehicle environment.
2. The climate control unit drives the airflow mode actuator according to the results of the airflow mode determination and corrections.
Airflow Mode Actuator [Full Auto Air Conditioner]
Purpose
The airflow mode actuator moves the mode door in the A/C unit to switch the
air vent.
Function
Door open/close function
The airflow mode actuator drives the motor based ...
Airflow Temperature Control [Full Auto Air Conditioner]
Purpose
The airflow temperature control changes the airflow temperature according
to the vehicle conditions.
Function
The air mix actuator is driven and the air mix door positio ...
Other materials:
Passenger Compartment Temperature Sensor Removal/Installation [Full Auto Air
Conditioner]
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Front scuff plate (driver-side).
b. Front side trim (driver-side).
c. Switch panel.
d. Decoration panel.
e. Shift lever knob (MTX).
f. Front console box.
g. Shift panel.
h. Upper panel.
i. Rear console. ...
Airflow Mode Actuator Inspection [Full Auto Air Conditioner]
CAUTION:
If the lever position exceeds the operation range shown in the figure, the
circuit in the actuator could be damaged. Always perform an actuator operation
inspection with the lever movement within the range shown in the figure.
1. Connect battery positive voltage to airfl ...
Ion Sensor Inspection
DTC Inspection
1. Connect the M-MDS to the DLC?2.
2. Perform the DTC inspection using the M-MDS..
If any DTC related to the ignition coil/ion sensor is present, repair the
malfunctioning location according to the applicable DTC troubleshooting..
Visual Inspection
NOTE:
B ...
