The ignition must be switched ON for the power windows to operate.
WARNING
Make sure the opening is clear before closing a window:
Closing power windows are dangerous. A person's hands, head, or even neck could be caught by the window and result in serious injury or even death. This warning applies especially to children.
Never allow children to play with power window switches:
Power window switches that are not locked with the power window lock switch would allow children to operate power windows unintentionally which could result in serious injury if a child's hands, head or neck becomes caught by the window.
CAUTION
To prevent burning out the fuse and damaging the power window system, do not open or close more than three windows at once.
Operating the Driver's Side PowerWindow
Normal opening/closing
To open the window to the desired position, lightly hold down the switch.
To close the window to the desired position, lightly pull up the switch.
Auto-opening/closing
To fully open the window automatically, press the switch completely down, then release. The window will fully open automatically.
To fully close the window automatically, pull the switch completely up, then release. The window will fully close automatically.
To stop the window partway, pull or press the switch in the opposite direction and then release it.
Power window system initialization procedure
If the battery was disconnected during vehicle maintenance, or for other reasons (such as a switch continues to be operated after the window is fully open/closed), the window will not fully open and close automatically.
The power window auto function will only resume on the power window that has been reset.
1 Switch the ignition ON.
2 Make sure that the power window lock switch located on the driver's door is not depressed.
3 Press the switch and fully open the window.
4 Pull up the switch to fully close the window and continue holding the switch for about 2 seconds after the window fully closed.
Jam-safe window
If a person's hands, head or an object blocks the window during the autoclosing operation, the window will stop and open halfway.
WARNING
Make sure nothing blocks the window just before it reaches the fully closed position or while holding up the power window switch:
Blocking the power window just before it reaches the fully closed position or while holding up the power window switch is dangerous.
In this case, the jam-safe function cannot prevent the window from closing all the way. If fingers are caught, serious injuries could occur.
NOTE
• Depending on driving conditions, a closing power window could stop and start opening when the window feels a shock that is similar to something blocking it.
In the event the jam-safe function activates and the power window cannot be closed automatically, pull and hold the switch and the window will close.
• The jam-safe window function does not operate until the system has been reset.
Engine-off power window operation
The power window can be operated for about 40 seconds after the ignition is switched from ON to off with all doors closed. If any door is opened, the power window will stop operating.
NOTE
For engine-off operation of the power window, the switch must be held up firmly throughout window closure because the auto-closing function will be inoperable.
Operating the Passenger Power Windows
The power windows may be operated when the power window lock switch on the driver's door is in the unlocked position.
The passenger windows may be opened or closed using the master control switches on the driver's door.
To open the window to the desired position, hold down the switch.
To close the window to the desired position, pull up the switch.
PowerWindow Lock Switch
This feature prevents all power windows from operating, except the driver's power window. Keep this switch in the locked position while children are in the vehicle.
Locked position (button depressed):
Only the driver's power window can be operated.
Unlocked position (button not depressed):
All power windows on each door can be operated.
Mirror Base Installation
1. Cut away all of the original sealant using a razor.
WARNING:
Using a razor with bare hands can cause injury. Always wear gloves when using
a razor.
2. Clean and degrease the ceramic coating on the glass and the base.
CAUTION:
Keep the area free of dirt and grease, and ...
Wheel Hub Component Removal/Installation [Awd]
CAUTION:
Performing the following procedures without first removing the ABS wheel-speed
sensor may possibly cause an open circuit in the wiring harness if it is pulled
by mistake. Before performing the following procedures, disconnect the ABS wheel-speed
sensor connector (body side) ...
PID/Data Monitor Inspection [Front Body Control Module (Fbcm)]
1. Connect the M-MDS to the DLC-2.
2. After the vehicle is identified, select the following items from the initialization
screen of the M-MDS.
a. Select “DataLogger”.
b. Select “Modules”.
c. Select “F_BCM”.
3. Select the applicable PID from the PID table.
4. Verify the PID ...