Mazda CX-5 Service & Repair Manual: Suspension
- General
- General Procedures (Suspension)
- Rear Trailing Link Removal/Installation
- Rear Wheel Hub Bolt Replacement
- Suspension
- Suspension Abbreviations
- Suspension Features
- Wheel Hub Component Inspection
- Wheel Hub Component Removal/Installation [2 Wd]
- Wheel Hub Component Removal/Installation [Awd]
- Front Suspension
- Front Axle
- Front Lower Arm Inspection
- Front Lower Arm Removal/Installation
- Front Shock Absorber And Coil Spring Disassembly/Assembly
- Front Shock Absorber And Coil Spring Removal/Installation
- Front Shock Absorber Disposal
- Front Shock Absorber Inspection
- Front Stabilizer Control Link Inspection
- Front Stabilizer Removal/Installation
- Front Suspension
- Front Wheel Hub Bolt Replacement
- Wheel Hub, Steering Knuckle Inspection
- Wheel Hub, Steering Knuckle Removal/Installation
- Rear Suspension
- Rear Axle
- Rear Coil Spring Removal/Installation
- Rear Drive Shaft
- Rear Drive Shaft Disassembly/Assembly
- Rear Drive Shaft Inspection
- Rear Drive Shaft Removal/Installation
- Rear Lateral Link Removal/Installation
- Rear Lower Arm Removal/Installation
- Rear Shock Absorber Disposal
- Rear Shock Absorber Inspection
- Rear Shock Absorber Removal/Installation
- Rear Stabilizer Control Link Inspection
- Rear Stabilizer Removal/Installation [2 Wd]
- Rear Stabilizer Removal/Installation [Awd]
- Rear Suspension
- Rear Upper Arm Removal/Installation [2 Wd]
- Rear Upper Arm Removal/Installation [Awd]
- Wheels, Tires
- Wheel Alignment Pre Inspection
- Wheel Apron Component Installation [Panel Replacement]
- Wheel Apron Component Removal [Panel Replacement]
- Wheel Balance Adjustment (Aluminum Alloy Wheel)
- Wheels And Tires
- Tire Pressure Monitoring System (TPMS)
- Tire Pressure Monitoring System Initialization Procedure
- Tire Pressure Monitoring System Set Switch
- Tire Pressure Monitoring System Set Switch Inspection
- Tire Pressure Monitoring System Set Switch Removal/Installation
- Tire Pressure Monitoring System Warning Light
- Tire Pressure Warning Alarm
Bsm Indicator Light Flashes While Not Under Bsm Indicator Light Flashing Conditions
(No Combination Switch Operation (Turn Signal Switch)) [Blind Spot Monitoring (Bsm)]
Description
BSM indicator light flashes while not under BSM indicator light-flashing
conditions (no combination switch operation (turn signal switch)
...
General
...
Other materials:
Liftgate Hinge Removal/Installation
1. Disconnect the negative battery cable..
2. Remove the following parts:
a. Rear scuff plate.
b. Trunk end trim.
c. Trunk side trim.
d. C-pillar trim.
e. D-pillar trim.
f. Liftgate.
3. Remove fasteners.
4. While partially peeling back the rear part of the headliner, remove nut ...
Throttle Body Inspection
Resistance Inspection
1. Disconnect the negative battery cable..
2. Disconnect the throttle body connector.
3. Measure the resistance between throttle body terminals E and F.
Throttle body resistance
1.38 ohms [20°C {68 °F}]
If not as specified, replace the throttle ...
Power Metal Oxide Semiconductor Field Effect Transistor (Power Mos Fet) [Full
Auto Air Conditioner]
Purpose
The power MOS FET controls the blower motor rotation speed.
Function
The power MOS FET controls the supply voltage to the blower motor based on
the gate voltage sent from the climate control unit, and adjusts the fan rotation
speed (airflow volume).
Constructi ...
